Residential · Lakeland, FL
When a garage or shop floor starts peeling, bubbling, or tire-lifting, patching rarely lasts. Elite Epoxy Lakeland removes failed coatings down to sound concrete and installs a new epoxy or polyaspartic system built to bond and wear in Lakeland.
Good results start with the base, not the topcoat. We inspect the slab for laitance, old paint, moisture issues, oil contamination, and hollow or delaminated areas, then choose the right epoxy removal method: diamond grinding with HEPA dust control for most floors, or shot blasting for heavy build coatings and profile needs. After coating removal we repair cracks and spalls with epoxy mortar or polyurea crack filler, address control joints as needed, and verify the surface profile (typically CSP 2-3 for most epoxy systems) before any primer goes down.
Local heat, humidity, and daily use drive material and finish choices. For many projects we use a moisture-tolerant epoxy primer where needed, then build with 100% solids epoxy for body and optional full-flake broadcast for slip resistance and uniform appearance. If you want faster return to service and better UV stability near doors, we can finish with a polyaspartic or aliphatic urethane topcoat and add aluminum oxide or silica traction additive for safer wet performance. Final sheen is selectable (satin to gloss), and we set expectations for cure times, vehicle traffic, hot-tire pickup resistance, and chemical exposure based on your use.
Lakeland customers choose us because removal is where corners show, and we do not skip it. Our crew is licensed and insured, provides a free written estimate, and explains exactly what failed, whether it was poor prep, low-solids DIY epoxy, moisture vapor, or incompatible layers. We use commercial grinders, proper diamonds, and dust extraction to keep the job clean, and we document the prep so you know the floor is ready for primer, not just scuffed up.
Before we wrap up, we walk the floor with you and confirm coverage at edges, stem walls, and transitions, plus any anti-slip level you requested. You get clear care instructions for the first week (cure, cleaning, and what to avoid), along with a maintenance plan for periodic washing and spill cleanup so the new coating stays tight. If we find slab issues that affect long-term bond, we explain options up front, including additional grinding, moisture mitigation primer, or spot repairs, so the recoating performs the way it should.
Yes. We provide a free written estimate that outlines prep, coating layers, finish, and expected downtime.
Sometimes. We evaluate the existing coating, test adhesion, and typically grind to a sound layer or remove failed material. If the old coating is peeling or soft, it needs removal and proper profiling.
Common options include solid color epoxy, full or partial flake broadcast, quartz systems, and metallic epoxy for decorative interiors. Topcoats can be polyaspartic or polyurethane, with optional traction additives.
Glossy finishes can be slick with water or oils. We can add aluminum oxide or polymer grit, adjust texture, and recommend the right finish for garages, pool decks, and commercial areas.
Typical causes include moisture vapor pressure, contaminated concrete (oil, silicone, curing compounds), insufficient surface profile, or coating outside the recoat window. Proper testing, grinding, and product selection prevent most failures.
Epoxy removal is the difference between a floor that lasts and a floor that fails again. If your coating is peeling, bubbling, chalking, or lifting under hot tires, the fix is usually full removal to a clean, profiled slab, then a properly layered epoxy or polyaspartic system. Elite Epoxy Lakeland handles coating removal and recoating for garages, warehouses, showrooms, and back-of-house commercial spaces throughout Lakeland, with a process built around concrete prep and bond strength.
Most failed coatings trace back to poor prep or incompatible layers, such as low-solids epoxy kits over smooth concrete, paint under epoxy, or a glossy sealer that never allowed mechanical bond. Our epoxy removal process typically includes testing for moisture concerns, degreasing oil-stained areas, then mechanically removing the old coating with diamond grinders or shot blasting until we reach sound concrete. We target the right concrete surface profile (often CSP 2-3 for epoxy) so primers and base coats can lock in.
After removal, recoating is built as a system, not a single coat. Depending on your goals, we may install a moisture-tolerant epoxy primer, a 100% solids epoxy base, vinyl color flakes or quartz aggregate, then a UV-stable polyaspartic or urethane topcoat. In work areas we can add aluminum oxide grit for traction and specify a finish that balances cleanability with slip resistance.
If you need epoxy removal in Lakeland, we will inspect the floor, explain what failed, and provide a written scope that matches your use, from daily parking to pallet jacks and chemical exposure. The goal is straightforward: remove what is unsound, prepare the concrete correctly, and recoat with materials designed for long-term adhesion and wear.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Lakeland. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
